Here is one of many style Gas Fuel Bowsers that our team custom built to be used on an assembly line to fill units that have missed the fuel station for any number of reasons. The unit is designed with a Wilden Pump, ground reel, level gauge and a Fill-Rite meter to dispense accurate amounts […]
Check out this gas skid that we pulled out of a Michigan automotive assembly plant. We completely tore down and refurbished the skid and it is now being installed at a Chicago automotive assembly plant. You can see by the original condition of skid that the biggest challenge was getting it to look new again […]
Pictured is a skid designed to transfer batches of Glycol off rail cars and into tanker trucks. To achieve this, a Blackmer MS3 Magnes pump was coupled to a Nord gearbox and a WEG 10 HP explosion proof motor. This assembly pumped the Glycol through an Endress Hauser ProMass Coriolis flow meter to totalize the […]
These Wilden Pro-Flo Shifts AODD pump stands were supplied to a chemical manufacturer for pumping a variety of different chemicals. The stands consisted of Wilden Pro-Flo Shift pump, IFC Y-Strainer, Wilden Pulsation Dampener (not pictured), Dixon air shut off valve, RTI air filter, coalescer, regulator, and (2) Hose Master Flex connectors (not pictured). The components […]
We were visiting Gusher Pumps when they were testing a Gusher 7550 Vertical Centrifugal pump for one of our customers. This pump was designed for 870 GPM at 115 Feet of Head of water-based fluid. This was one of multiple pumps that were built and after testing getting sent to the paint booth for a […]
Business is slow for many, but that doesn’t mean you can’t remain productive. If you have equipment sitting idle due to partial shutdowns, now might be a good time to perform preventative maintenance to ensure they perform as needed when full production returns. Small investments now can help you avoid significant damage on pumps and […]
A customer brought us their Blackmer CRL4B Sliding Vane Pump used for pumping CO2, because they were not experiencing the longevity needed from their pump to fulfill application demands. The pump would work for a limited time and break down. The last repair shop the customer used to repair the pump did a number of […]
Pictured is a ANSI pump assembly that an automotive supplier brought in due to a leaking seal. Luckily in this case, there were no major parts needed. A standard overhaul was done on the pump. All the common wear items, including new ball bearings (pump and motor), mechanical seal, gaskets, O-rings, a coupling insert were […]
A major asphalt paving company needed their Viking KK4124A internal gear pump for pumping hot oil overhauled. The wear was evident on the rotor, shaft and the pump’s mechanical seal was leaking. The seal flush line was also not set at the correct orientation. After modifying the seal flush line, so it was set at […]
Hose crimping can provide a safer, more reliable hose assembly than many other hose fitting attachment options. Ensuring you are taking the right steps to crimp your hose properly is of the utmost importance in regards to safety and system function. Follow these steps for proper hose assembly: 1. Select the hose, fittings and ferrules […]
Here is a cooling skid we just finished for a customer that is using the skid to cool engine coolant, oil, fuel and air at an engine manufacturer. We are pumping a 50% glycol mixture and cooling it down from 195°F to 133°F at 80 GPM. This was developed for a test stand that is […]
Pictured below is a cooling skid designed for an orthopedic product manufacturer who makes artificial replacement parts for the human body. The customer needed a way to keep the air compressors and air dryer used in their production process from overheating. Our solution was a system that utilizes a cooling tower. The system recirculates cool […]
With so many options to choose from in today’s day and age, buying the right pump for your application can initially feel like an overwhelming task. A task that can cost you time and money if not approached correctly. Providing detailed and accurate information is essential to finding the best pump for your application. That […]
An engineered coating manufacturer needed their Kerr 5500 Series Vertical Process Pump repaired. As seen in the pictures below, excessive scale buildup inside and outside of the pump’s wet end caused the pump to seize or completely lock up. The shaft unfortunately needed to be replaced due to wear in critical areas. After replacing the […]
Choosing the right positive displacement pump can be a challenging endeavor. A rotary vane pump maybe the right choice depending on the application, media and environmental circumstances. What are rotary vane pumps and how do they work? Check out the article below on the ins and outs of rotary vane pumps. What is a Rotary […]
Pictured is a Roots 68-URAI rotary lobe blower for a leading producer of cement and other building materials. The customer brought us several of these units that needed repair, hoping to save money instead of having to buy brand new units. However, the units were in poor condition, with most needing major parts to function, […]
Commonly used in several industries, including adhesives, petroleum, cleansing/lubricating products, confectionary and more, internal gear pumps are one of the key pieces of industrial equipment in the production line. What is an internal gear pump and how does it work? What roles does it play in industry? The following article explores the intricacies of internal […]
In many industrial sectors, vacuum pumps are doing yeoman’s work. Often running for several hours per day in some applications and even non-stop for multiple work shifts per day. Vacuum pumps being in operation means several maintenance related issues inevitably will crop up. If the user is not proactive in treating these issues the vacuum […]
Industrial pumps carry out many different responsibilities at industrial and commercial facilities. To shoulder the weight of these responsibilities, industrial pumps consume a great deal of electricity. Improving the energy efficiency of industrial pumps can lead to outstanding energy savings and increased longevity. The article below discusses 8 great ways to enhance industrial pump performance […]
This Ampco SLH-4G Twin Screw pump was built by Ampco Pumps and didn’t come with a protective shroud around the motor when it arrived at the customer’s facility. The customer was keen on having a protective shroud around the motor. No problem! We fabricated the pictured stylish shroud for them that surrounds the motor. It […]
Some applications can be more challenging than others and require creative solutions. With over 50+ years of experience in the fluid technology field, Anderson Process has the knowledge and resources at its disposal to provide unique solutions for persistent issues. Our customer had an FDA-rated steam hose that descended from a unit to clean the […]
A customer involved in providing environmental and agronomic systems needed a recirculation pump for their process. They handle chemicals and fuels that can potentially be hazardous if contaminated, so they required a reliable solution that would reduce the risk of fluid contamination. We engineered this Gusher pump with AES seal pot as a solution to […]
Industrial pumps and equipment operate in some of the most extreme working conditions. Over time certain physical impacts, moisture, chemicals, and ultraviolet light can cause corrosion and deterioration of parts, resulting in at worst a breakdown or at best a beaten down appearance. To combat this process Anderson Process offers powder coating finishes to skids […]
A customer’s worn Viking asphalt pump was in rough shape. One of our experienced technicians refurbished the pump and the difference is night and day. View the astonishing transformation in the pictures below. Anderson Process is an authorized service center for many of the top pump manufacturers in the marketplace. Some of our capabilities include […]
Pictured is a Split Case Pump that had obvious past repair issues. The pump was brought to Anderson by a customer that made rolled aluminum products. Among the chief issues, the impeller clearance and shaft sleeves were not set properly, which resulted in severe wear to the entire rotating assembly. As a result, the shaft […]
One of our customers needed a solution to a 10-year-old mixing issue that was driving up operation costs in their facility. The process involves producing a water/polyvinyl acetate emulsion mix that is used as a bath for premoisturized fabric to be coated. The fabric coating requires an extremely consistent mix, and their existing equipment was […]
Here we helped a customer build a series of chemical treatment recirculating skids that heated and filtered the chemical before it was sent off to the process. The overall system was designed for 75 GPM at 40 PSI. We utilized a Goulds 3756 centrifugal pump, Standard Xchange Plate & Frame heat exchanger, Eaton Filters, Dixon […]
What special needs do you have for your filtration applications? Proper filtration enhances many industrial fluid applications, increasing the purification of water, chemicals, and other fluid output. Efficient filtration in markets such as automotive, food & beverage, chemical, pharmaceuticals, power generation, water and wastewater can save valuable resources that effect an organization’s bottom line. Anderson […]
Here are Blackmer pump skids designed and built by our team for a chemical manufacturing company to pump solvents. The assemblies consist of Blackmer Magnes pumps coupled to Nord Gear reducers and WEG motors. The Nord Gear Reducer (between the WEG Motor and Blackmer Magnes pump) converts the high speed, low torque input from the […]
A chemical manufacturer was looking for an efficient unit to pump chemical solvents that would align properly with the piping they had in place. The pictured assembly consists of a Blackmer Magnes pump coupled to a Nord gear reducer and 10 HP WEG explosion proof motor mounted on a custom fabricated powder coated frame. The […]
Being able to read positive displacement pump curves is important to determine a pump’s ability to produce flow under several conditions, such as viscosity and differential pressure, which can affect pump performance. It is also vital to understanding what the pump is capable of and how to possibly diagnose issues that arise. The following article […]
Here are some PVC hose assemblies with camlock ends that Anderson Process crimped and assembled for a customer in the construction industry. These heavy-duty hoses are both flexible and durable with a rigid orange helix. The hoses are made for demanding applications and in this case were being used to transfer water on a construction […]
An industrial gas supplier needed their Blackmer pump for pumping propane restored. Upon arrival, the signs of wear were obvious. The outside of the pump was weathered and corroded. It even seized up when attempting to start it. When the pump was disassembled, the inner parts, including the vanes, casing liner, rotor and head discs, […]
This Mouvex Metering Pump Skid was designed for a pharmaceutical manufacturer. Its primary function is metering water. The skid consists of a Mouvex SL4 Pump, A WEG 2HP Motor, A Micro Motion 2500 Series Meter, 30 AMP Disconnect Safety Switch, 480 Volt Panel, 24VDC Controls, Allen Bradley VFD, Stainless Steel Sanitary Fittings and Ashcroft Gauges. […]
This tank system filters the incoming product, and heats the oil to a set temperature.
Customer: Food Manufacturer Need/Application: Customer wanted a heated mix tank with batch metering capabilities that would fit into their elevator and be fully portable. Solution: The system included: Ampco pump, Xylem multi-stage pump, control panel build to our specifications, air actuated three way valve, electric heater to heat the glycol/water mixture, jacketed tank, Micro Motion meter and a Sharpe […]
Customer: Chemical Manufacturer Need/Application: Needed to pump chemicals from rail cars with the following requirements… Maximum of 20 ft. lift 80 GPM flow rate Working pressure of 60 PSI Solution: This was made possible by building a four skid unit equipped with a variety of products. This complex system included air actuated ball valves, Micro Motion meter, Mouvex pump, […]
Customer: Power Plant Need/Application: Customer was using 2 peristaltic hose pumps to meter water into a burner stack for pollution control with a third pump as back-up. This then made them have to change the hoses about every 5-6 weeks of use and had no way to control the water into the pumps. That was a big […]
Custom Solutions is a cornerstone of our business. We regularly create custom solutions for customers, ranging from simple skids for general use to elaborate pump systems that meet the need of very specific applications. This is an example of one of our larger projects where the customer needed a packaged solution to moving and treating […]
Precise control mixing of materials can be a challenging feat. Understanding the chemical compatibility and how the liquid properties will react, blend, and change must be closely monitored. Pictured below are several different pumps and a control system we set up for a customer who needed to meter three liquids: propylene glycol, ethanol, and water […]
This Standard Pump tote batching system was designed for a battery supplier, who was interested in a system to batch battery acid (sulfuric acid) out of a tote and into jugs. Pictured is the system we designed. A Standard stick pump was used for pumping the battery acid from the tote. A stainless steel bridge […]
Do you have a unique fluid fill process that needs to be addressed? We’ve shown other Fluid Fill Bowsers before – most recently a Windshield Washer Bowser. The one below is a Gasoline Bowser with a Wilden Pump and Engineering Air-Operated Double Diaphragm pump. This double diaphragm design will ensure precise amounts of gasoline are […]
Customer: Gearbox Manufacturer Need/Application: Customer wanted to meter pre-set amounts of oil into gearboxes from totes and have the system be fully portable. Solution: We made this possible by designing a custom skid that was made up of a Wilden pump, Blacoh pulsation dampeners, control panel with a Badger Meter batcher, meter, casters, hoses and a shut-off nozzle. The […]
Our repair team here at Anderson Process is uniquely positioned to deliver superior refurbishment and aftermarket services for even the most complex liquid process equipment challenges. Here are some pictures of two Total Control Systems (TCS) 682 Piston Meter rebuilds that were just finished. These meters came to us out of calibration and with worn parts after […]
Customer: Machine Manufacturer Need/Application: Needed to batch and mix coating material at two different strengths and supply it to their production lines. Solution: This was made possible through the design of a two tank system with Wilden pumps to pump product from totes into tanks and from tanks to production lines. All of the piping, pumps and valves […]
We recently finished and installed Phase 1 of an engineered, designed and built Stainless Steel platform system that will help assist in the manufacturing of product once completed for a local Food manufacturer. Phase 2 will consist of alterations to tanks and mixing equipment to improve the efficiency of food production. The platform system will […]
Our Michigan facility built several stainless-steel tanks to be used by an industrial laundry service company. They offer cleaning of tough, gritty materials such as oil absorbents, industrial towels, and floor mats that are used in various manufacturing facilities. They previously used polyethylene tanks in their facility to hold the materials used for their cleaning […]
Just finished up repairing a Sharpe mixer to start off the week! The repair included replacing the bearings, seals, shaft and we finished it off with a fresh new paint job.
These are two portable Ampco pump skids built for a pharmaceutical and cosmetics contract manufacturer. They feature Ampco ZP1-060 pumps, along with Nord gear reducer, and a WEG motor mounted on a stainless steel cart with a WEG washdown VFD. Anderson Process continues to be a reliable service provider to many manufacturers throughout the Midwest. […]
Check out these Mouvex H-FLO 25 eccentric disc pump skids we designed for a manufacturer of antiseptic products to pump glycerin. The skid incorporated the Mouvex pump, a Nord gear reducer and a Baldor white washdown motor all mounted on a stainless steel sanitary base plate we fabricated (including welding) at our facility. As you […]
We just put the finishing touches on these sharp looking, Blackmer GNX3 Pump Stands designed for a chemical manufacturer to pump a variety of different chemicals. The stands consist of Blackmer GNX3 pumps with an integral Nord gear reducer and a WEG explosion proof motor mounted on a steel frame we fabricated at our facility […]
A vacuum pump is a device that removes gas molecules or air particles from a sealed volume in order to achieve difference in pressure creating a partial vacuum. Vacuum pumps are designed in a variety of technologies based on the pressure requirements and the application it services. When setting up a vacuum pump system, sizing […]
Here is a transmission fluid fill system that has helped provide a customer with the capabilities of filling multiple transmission fluids. Engineered by the Anderson Process Michigan ACI Systems Engineering Department and fabricated from the ground up by the Anderson Process Michigan Fabrication division. This is only one of two fill systems that have been […]
Anderson Process has recently worked with another customer to solve their fluid transport and storage needs. Challenge: The customer was looking to move from drum and tote delivery of ethyl acetate to a centralized storage system. Solution: Anderson Process provided them with 2 outdoor 5,200 gallon double walled tanks and 2 indoor 500 gallon double […]
We offer a variety of Fluid Fill Systems and Components that service automotive assembly plants and manufacturing plants. One of our portable offerings are called Bowsers, these Bowsers are portable fluid dispense systems containing hazardous and non-hazardous liquids. This system was a Windshield Washer Fluid bowser consisting of a Wilden Air Operated Double Diaphragm pump, […]
Here we are finalizing the mechanical aspect of a unit designed for Gas and Oil fill at a small engines / power equipment plant in the Southeast US. The customer came to us with a manual process in place and we worked with them to automate the process the best we can. There is a […]
Anderson Process Fluid Fill Systems create semi-automated systems to dispense hazardous or non-hazardous liquids in small but precise amounts to test a large range of vehicles during the manufacturing process.
We just finished a complete overhaul repair of a Pioneer Vacuum prime assist centrifugal pump, this was one in a series of pumps getting re-built. The Prime Series from Pioneer are ideal in situations where you can leave the pump unattended in order to self-prime itself in remote locations. Examples of this are in agriculture fields, […]
A chemical manufacturer’s Kinney (Tuthill) 2-stage liquid ring vacuum pump’s seals were leaking prematurely due to hard water correlated issues at their facility. After exploring some different options with the customer to extend seal life, they opted for us to rebuild the pump to factory specifications. We replaced the wear parts (seals and bearings) and […]
Here are four Blackmer pump skids we built for a customer in the chemical industry. The customer needed a solution to be able to pump chemical solvents at a controlled speed. The skids we built consist of a Blackmer Magnes Pump, a Nord Gear Reducer and a WEG explosion proof motor. The pictured skids are […]
Modern winery facility utilizing stainless steel containers compared to old style wooden barrels.
John Vorpagel (Anderson Process) and Mike Solso (Blackmer Gear Pumps, formerly EnviroGear Pumps) sit down to discuss mechanical seals, seal-less technology, and Envirogear® E Series Magnetically Coupled Seal-less Internal Gear Pumps in their first video series, “2 Guys Talk About Pumps”. Check out the first series of short videos below: Face it, Mechanical Seals are […]
In 2014, EMCO opened a new large-scale terminal facility that needed efficient, low-maintenance pumps. Because of the critical nature of these storage areas, it was imperative for EMCO to identify the right brand and style of pump that would be used to unload railcars of raw materials and load totes, drums and IBCs with finished […]
Increasing output and efficiency is a common goal for all manufacturers. Customers often come to Anderson Process looking for ways to improve their fluid handling applications. Our experienced Territory Managers are there every step of the way, from initial walk-thoughs and recommendations to full implementation. Here’s another production improvement designed and coordinated by the AP […]
Custom carts and skids are one of our main areas of expertise. Often times, multiple permanent filtering solutions are not a financial or efficient reality for our customers. As a solution, mobile carts can be kitted with the proper equipment and used in multiple locations depending on which system has the need at any given […]
Here are some pumps that were built for a food production facility, they are using Mouvex Eccentric Disc Pump assemblies for pumping Chocolate and Flavorings. The order consisted of 8 pumps total, ranging from an Mouvex’s largest SLS Series pump, the SLS36 that is designed for up to 158 GPM, down to their model SLS12, […]
Several years ago the Anderson Process team custom engineered a pump skid for a gravel pit customer moving large amounts of aggregate. The pump consisted of a large Pioneer GS8 Pump Assembly designed for pumping water 2,000 GPM at 60 Feet of head. The self-priming, solids handling, centrifugal pump was put on a fabricated steel […]
We just finished a complete overhaul of a Sundyne LMV 811 API pump for a local Wisconsin Power Plant. Commonly found for pumping boiler feed water, condensate services or desuperheating, these pumps are key to keeping power plants up and running for power production. We did a complete rebuild of this pump, including a gearbox […]
We recently built two custom pump carts for a local customer that manufacturers cleaning and sanitation chemicals. They wanted to minimize the amount of pumps needed and create a flexible solution for transferring chemicals from totes to a mixing tank to be blended for their customer’s specific needs. The pump carts needed to have a […]
We have built a few of these carts over the years for a local Chemical manufacturer, this one that we just shipped out was no different. The pump assembly is used to transfer and recirculate an Aluminum / Solvent Slurry through a mill to reduce particle size. This pump was built on a cart so […]
There are many different types of pump technologies that can be used for injection of different types of additives. The technology that is used for the addition of additives would depend on the types of flows, pressures, viscosities, chemical compatibility to name a few of the items that help us narrow down the proper pump […]
These Ampco ZP Pump Skids were built for a Dairy / Cheese Manufacturer that Anderson Process has serviced for many years. The skids are for an expansion in the facility, and are duplicates of pumps we have previously built for the same company as they continue to increase production. Over the years we have been […]
Here’s a large order we shipped out for a local candy manufacturer. These assemblies are Mouvex SLS1 Pumps coupled to Sterling Gearmotors. These pumps will be used to pump / inject oils and additives into the candy. Mouvex® SLS Series Eccentric Disc Pumps have been designed for use in a wide range of pumping applications […]
Our capabilities extend beyond fluid handling systems. The Anderson Process shop crew is also proficient in custom fabrication to meet a variety of needs. Below is a large stainless steel motor control panel built for a global automation customer that needed to house outdoor motor & pump controls. The customer needed easy access to the […]
One of the many reasons mechanical seals may need extra lubrication, include the high viscosity in certain fluids These pumps and mechanical seals may require the circulation of a clean fluid from an external seal flush. This process lubricates the inner and outer seal faces which separates the pumped fluid from entering the stationary housing […]
We built a custom skid for a customer who needed to pump asphalt, a hot and aggressive material. Systems that handle these types of materials need to be able to handle unplanned disruptions in the system in regards to temperature and viscosity. Featured on this skid is a Blackmer 8” HXL sliding vane pump, a […]
When it comes to energy production, water plays a crucial role. Used as the main cooling source, it is a critical component in how these complex systems operate. Organic and inorganic substances in water create dissolved solids that along with other pollutants can cause buildup and corrosion. High-quality filters with high micron filter media, that […]
Two Blackmer Gear (formerly EnviroGear) E series pumps featured on this skid have unique superior design features to allow longer life cycles then other mechanically sealed or seal-less internal gear pumps on the market. What creates this distinct feature, the Between-the-Bearing System, a specially designed spindle that protects the rotor and idler gear from hydraulic […]
Resins are naturally occurring as a plant substance but are often made synthetically, converted into polymers to be used in numerous applications. When pumping certain resins the biggest factor to consider is their viscosity, as they can vary from a thin syrup to a solid substance. Resins can be difficult to handle as they can […]
We custom fitted a 1” Wilden Stainless Steel FDA pump on a heavy-duty stainless steel hand cart with an RTI filter regular and Continental hose for the air input to the pump. This Wilden Full Stroke Diaphragm pump was used to transfer FDA Oils and Ingredients. It was built on a cart to optimize it […]
This Cat high-pressure pump skid is used for flushing out cement drums commonly found on job sites or in cement mix plants. This is a triplex positive displacement pump meaning it has three plunger rods suitable for multi-gun and multi-nozzle high-pressure systems. It features max flow up to 15.6 gpm and a max pressure up […]
Don’t let old or worn-out seals hold your pump system back. Mechanical seals offer your rotating equipment the ability to be sealed in a cost-effective yet efficient manner. Mechanical seals contain the high pressurized fluid within pump vessels from the low pressured environment outside of the pump vessel. Our repair services can get your mechanical […]
This custom skid features three Goulds Water Technology e-SV pumps designed to boost the flow of city water into production rooms for a food manufacturer. During the Summer months, the water pressure would drop significantly, and the customer had trouble providing consistent flow to the far side of the facility. This was especially problematic when […]
Hose selection is critical to not only production output reliability, but also to user/environmental safety. Anderson Process’s comprehensive line of hose assemblies and hose fittings, combined with our maintenance-tracking and reconditioning support services, help our customers realize consistent and safe material containment, movement, and transfer. Pictured here are 2” Novaflex Red Uni-flon Composite hoses with […]
This 2” Wilden Pro-Flo Saniflo pump was mounted on a stainless steel cart that would replace the customer’s older Wilden Foodmaster. The Wilden Saniflo pumps are FDA approved and designed for standard food applications. They are typically used for processes that are moving high-acid, high-sugar, and high-fat media. This particular diaphragm pump is all stainless […]
A custom skid we built for a customer that consisted of a 1-1/2” SS/Teflon Wilden Pump and Engineering pump, Blacoh AODD pulsation dampener, Blacoh SpillStop leak prevention system, RTI Eliminizer and air regulator, Bi-Torq ball valves, Continental Fortress air hose and Tudertechnica Glidetech hose. The discharge piping using on this cart was Schedule 80 with […]
Pictured below is a large skid we developed. The skid features a 10’’ BLACKMER® HXL10 vane pump coupled to a 161 HP diesel motor through a Nord Parallel shaft gear reducer. The gear shaft reducer was selected to handle the intense force and pressure applied, as the unit would be pumping fuel oil at 1650 […]
One of our many value-added services is hose audits and hose management programs. As part of these services, our specialists conduct an on-site inspection to ensure all hoses are being properly used and maintained, which is crucial to their service life and to reduce the risk of failures in production. Additional (optional) services of the […]
Global supply chain shortages prevented one of our customer’s bulk chemical supply from being delivered via railcar. They were able to purchase the chemical in 55-gallon drums as an alternative and needed a pump unit capable of line stripping to maximize product recovery. They also requested a run-dry capacity in the event a technician did […]
This fuel filtration skid was designed to filter underground fuel storage tanks that have become dirty/contaminated or contain large amounts of water. Our customer was wanting to pull up to fueling stations and have the ability to clean out their in-ground tanks with a variety of filtration capabilities. The final product is one of the […]
These Tuthill pump assemblies were fabricated for a healthcare technology company and used to pump hydraulic oil. They feature a Tuthill 2C2BV-C-7 rotary gear pump assembled with a Tuthill 2C1B534-56 NEMA C Frame mounting adapter and a Baldor CL3507 Motor (¾ HP, 1725 RPM, 1/60/115/230V). Anderson Process continues to be a reliable service provider to […]
This MixMor turbine mixer with mixing tank assembly was designed for a midwest chemical manufacturer. The manufacturer’s business was expanding, and they wanted a new mixer and tank to double their production rate. The assembly features a MixMor TC-20-L52 flange mounted turbine mixer with a TEFC Motor (20 HP, 1750 RPM, 3/60, 230/460 VOLT), gear […]
A customer in the HVCR (heating, ventilation, air conditioning and refrigeration) industry brought in their Busch WV1000 blower to be serviced. The blower or vacuum booster, resting on top of a Busch Cobra dry screw pump, was used for helium leak testing in the manufacturing process of commercial HVAC compressor systems. Debris had built up […]
Pictured is a Blackmer Gear G1-55 pump that was used for pumping a starch-based adhesive used in the manufacturing process of corrugated cardboard. The customer brought the pump in for a leaking seal. The seal unfortunately failed after pressures climbed above the seal’s operating pressure. The triple lip style cartridge seals used in this application […]
These Blackmer Gear G1-133 pump assemblies were built for an adhesives manufacturer for processing PVA adhesives (poly vinyl alcohol). They are made of stainless steel and have 4” flanges. An addition we provided was a stainless-steel guard around the stuffing box at the customer’s request for extra protection. We also welded risers on our standard […]
Blackmer’s eccentric disc pump – Mouvex Technology, is used in an array of applications across the globe.
Wilden has released a new video explaining how a Wilden Pro Flo X – PX1500 Air-Operated Double-Diaphram Pumps works.
Check out Volume 1 of BLACOH BUZZ where Gary L. Cornell of BLACOH Fluid Control, Inc. writes “The Necessity of Fluid Control” Part 1.
We hope you all had a great Labor Day weekend! Be sure to checkout Volume 2 of BLACOH BUZZ where you will find “The Necessity of Fluid Control” Part 2 by Gary L. Cornell. To read Part 1 please revisit the last post from Anderson Process.
Mann Tek Dry Disconnect Couplings are used for handling and transfer of liquids, gases and bulk powder in an economical, safe and environmental friendly way.
